HOMAN — Refined Supply GET A QUOTE
Standards Technical article

Bitumen 60/70 vs VG30: can one replace the other?

Only if the lot is tested and passes. Bitumen 60/70 is graded by needle penetration at 25 °C under ASTM D946, while VG30 is graded by absolute viscosity at 60 °C: 2,400–3,600 poise under IS 73:2013. A 60/70 lot can be accepted as VG30 only with a test report showing it meets every VG30 limit.

Key facts

  • 60/70: penetration of 60–70 tenths of a millimetre at 25 °C (100 g, 5 s, ASTM D5), as graded in ASTM D946.
  • VG30: absolute viscosity of 2,400–3,600 poise at 60 °C, kinematic viscosity of at least 350 cSt at 135 °C and penetration of at least 45 (IS 73:2013 Table 1).
  • IS 73 changed from penetration grading to viscosity grading in its third revision (2006). IS 73:2013 is the fourth revision.
  • IS 73:2013 recommends VG30 where the 7-day average maximum air temperature is 38–45 °C.
01 · GradingPenetration vs viscosity

What is the difference between a penetration grade and a viscosity grade?

A penetration grade is measured at 25 °C, so it is only an indirect guide to how the bitumen behaves on a hot road. A viscosity grade is measured at 60 °C, close to hot pavement temperatures, and at 135 °C, close to mixing temperatures. The foreword to IS 73:2013 gives the reason India changed: the variability in performance at high temperatures can be addressed by a specification based on viscosity at 60 °C instead of penetration at 25 °C.

02 · CompareASTM D946 · IS 73

How do the 60/70 and VG30 specifications compare?

Property Bitumen 60/70 (ASTM D946) VG30 (IS 73:2013)
Grading basisPenetration at 25 °CAbsolute viscosity at 60 °C
Penetration at 25 °C (0.1 mm)60–7045 min
Absolute viscosity at 60 °C (poise)Not specified2,400–3,600
Kinematic viscosity at 135 °C (cSt)Not specified350 min
Solubility in trichloroethylene99.0% min99.0% min
Aging testThin-film oven (ASTM D1754): retained penetration 52% minRolling thin-film oven residue: viscosity ratio at 60 °C 4.0 max; ductility at 25 °C 40 cm min
Grade selection guidanceNone in the standard7-day average maximum air temperature 38–45 °C

Sources: ASTM D946 Table 1; IS 73:2013 Clause 5 and Table 1. Compare HOMAN's Bitumen 60/70 datasheet and VG30 datasheet.

03 · SubstitutionTenders

Can 60/70 be supplied against a VG30 tender?

Only with VG30 test results. A penetration certificate does not show viscosity at 60 °C or 135 °C, or the viscosity ratio after rolling thin-film oven aging, and an IS 73 tender needs all of them. Some 60/70 lots fall inside the VG30 limits and some do not; only testing shows which. Ask for the report to IS 73:2013 before shipment, and read it against Table 1.

04 · VG40Hotter sites

When is VG40 the better choice?

IS 73:2013 recommends VG40 where the 7-day average maximum air temperature is above 45 °C. VG40 is the stiffer grade: 3,200–4,800 poise at 60 °C and a penetration of at least 35. See the VG40 datasheet or the grade selection guide.

HOMANHow we supply

How HOMAN tests and documents each lot

HOMAN has been active since 2016, with trade desks in Tehran and Shenzhen, and exports to buyers in 11 countries. Every lot is lab-tested in Bandar Abbas before shipment. Pre-shipment inspection is carried out by SGS or Geochem, as the buyer chooses. A Certificate of Analysis (COA) is issued for each order lot and tied to the batch number on the packaging.

Test reports to the buyer's required standard, including ASTM and IS 73. We quote EXW, FOB or CFR, with a minimum order of one container.

05 · FAQBuyer questions

Frequently asked questions

Is VG30 harder than 60/70?

Not necessarily. They are measured differently: VG30 by viscosity at 60 °C, 60/70 by penetration at 25 °C. VG30 only requires a penetration of at least 45, so a VG30 lot may or may not fall inside the 60–70 range. Compare test results, not names.

What is VG30 bitumen used for?

VG30 is a paving grade. IS 73:2013 recommends it where the 7-day average maximum air temperature is 38–45 °C.

Which test report do I need for an IS 73 tender?

A report to IS 73:2013 for the named grade, covering every characteristic in Table 1, including absolute viscosity at 60 °C, kinematic viscosity at 135 °C and the tests on the rolling thin-film oven residue.

06 · SourcesStandards cited

Sources

  1. Bureau of Indian Standards, IS 73:2013 Paving Bitumen — Specification (Fourth Revision): Foreword, Clause 5 (Grades), Clause 7 (Sampling), Clause 8.2 (Marking), Table 1 (Requirements) and Table 2 (Scale of sampling).
  2. ASTM International, ASTM D946/D946M, Standard Specification for Penetration-Graded Asphalt Binder for Use in Pavement Construction (current edition D946/D946M-25a), Table 1.
  3. ASTM test methods named in the text: D5 (penetration), D36 (softening point), D92 (flash point, Cleveland open cup), D2042 (solubility in trichloroethylene), D2170 and D2171 (kinematic and absolute viscosity), D1754 (thin-film oven test) and D2872 (rolling thin-film oven test).

Bulk · Drums · Jumbo bags · FlexitanksTrade desk quotation.

Specify the lot. Get a quotation.

Grade, tonnage, packaging, Incoterm and port — send those five lines and the trade desk issues a quotation.

Trade desk quotation on request.Every lot is lab-tested in Bandar Abbas before shipment. Pre-shipment inspection is carried out by SGS or Geochem, as the buyer chooses. A Certificate of Analysis (COA) is issued for each order lot and tied to the batch number on the packaging.

Request for quotationCOA per order lot

COA per order lot · Quotation on request.

Current commercial terms: under FOB, 30% advance payment and 70% against the agreed customs and shipping documents; under CFR, 30% advance payment and 70% after issuance of the Bill of Lading (B/L). EXW is also offered. Terms are agreed per contract.

Direct chartering or urgent vessel dispatch?

Direct Trade Desk